Exactly How To Install A Tub (For Novices).
Exactly How To Install A Tub (For Novices).
Blog Article
In this article below you can find a good deal of superb expertise in relation to How to Install a Bathtub Yourself.
Setting up a tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably tough task. If the old tub is easily easily accessible, the job can relocate speedily; if you have to open a wall to remove the old bathtub and position the brand-new bathtub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will need an assistant to vacate the old tub and also embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than employing a contractor to take control of a halfway-completed job, it is far better to take into consideration employing one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your washroom if you have actually currently gotten a brand-new bathtub and don't need to transform the arrangement of your previous water supply pipes.
Your tools and also product checklist should comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the supplier supplied backnut. When the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Using both wooden boards under its feet, put the tub in the needed position. The wood boards are useful in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub up until the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water and also check all joints as well as brand-new pipework for leaks and also tighten them if required. Fill up the bath tub as well as also examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's instruction manual. Tiling and also securing around the bathtub should wait till the bathtub has actually been utilized at the very least when as this will settle it right into its final placement.
Preparing for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, bring about problems with dampness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very interested by A Step-by-Step Guide to Installing a Bathtub and I'm hoping you appreciated the entire page. Don't hesitate to set aside a second to distribute this blog entry if you enjoyed it. Bless you for your time. Don't forget to check our blog back soon.
View Report this page